Sliverline 2 inch 6.5hp Petrol Engine 4 Stroke Water Pump - NEW

Silverline Tools established for over 30 years, are a leading industry expert in the manufacture and supply of hand and power tools.

Recognized and trusted throughout the UK and Europe, our management team and technicians are constantly striving to ensure Silverline tools meet and surpass all your DIY requirements again and again.

Offering a comprehensive and carefully selected range of products, we are dedicated to meeting current and future demands and are constantly evolving to ensure you get the very latest tools using up-to-date, cutting edge technology.

Recognized and trusted throughout the UK and Europe, our management team and technicians are constantly striving to ensure Silverline tools meet and surpass all your DIY requirements again and again.

Offering a comprehensive and carefully selected range of products, we are dedicated to meeting current and future demands and are constantly evolving to ensure you get the very latest tools using up-to-date, cutting edge technology.

Silverline Tools seem like they have been around since the invention of the wheel.

Silverline Tools trusted in the trade.

This model will pump water from the tube of 2 inches. The motor develops a pumping capacity of 200 litres per minute making a very high powered pump for the size and cost.

The pumps are self-priming centrifugal pumps designed to treat sewage water and clear water.

The simple disassembly of the cover lets you control and maintain the pump,

The water pump helps to water green areas, flower beds and garden.

Also suitable for powering irrigation systems.

For use in emergencies like flooding, emptying pools and outdoor water features, digs at construction sites and ponds.

Properly cared for and looked after, this pump will give you years of service.

Please note: Colour of the water pump can vary. Current stock is blue in colour.

Preparing your Water Pump

Your pump comes supplied without engine oil. Filling and checking the engine oil level should always be done before use.
Place water pump on flat level ground.
Unscrew dipstick (13) from oil filler neck (16)
Carefully pour in oil, of type and quantity in the specification
Wait a few minutes for it to settle.
Make sure the dipstick (13) is clean and dry, then screw it all the way back in to the filler neck (16)
Remove the dipstick (13) again, keeping the stick pointing down, as shown in Fig G.
The ideal level should be just below ÂœH1/2?
Top up as required to reach this level.

Assembling your Water Pump

Suction hose:

You now need to connect your reinforced suction hose (2) (Not supplied)
Make sure the hose is as short as practically possible.
Push the hose coupler (4) into your hose (2) as far as it will go. (Fig B).
Tighten the hose clamp (3) using a screwdriver or spanner.
Push the water filter (1) in to the other end of the suction hose(2)
Tighten another clamp (3) around hose (2) to secure.
Place a rubber seal (5) inside the hose coupler (4)
Screw the hose coupler on to the water inlet (24) tightly, by hand.
The discharge hose does not need to be reinforced.
Follow the instructions for Suction hose, but WITHOUT fitting a filter (1)

Priming your water pump:

With the water filter (1) fully submerged, and the discharge hose pointing to a suitable place, prime the pump.
Remove the cap from the water priming point. (26) by unscrewing it.
Fill the pump with water until it will not accept any more. (Fig. D)
Replace the cap in the water priming point (26)

Operating your Water Pump

Make sure your water pump is on firm level ground, prepared and assembled as described in this manual.

Fuelling:

Always refuel in a safe place, well away from the work area, and any source of heat or ignition. Avoid any contact with the fuel.
Only add fuel when the engine is stopped, and has cooled fully.
Remove fuel tank cap (6) and fill with fuel, see specification.

Starting the pump:

Set fuel lever (8) to ON move it fully to the right
Set choke lever (9) to ON move it fully to the left. NOTE choke should only be ON if the engine is COLD
Set speed control (10) to 1/4 (from right to left see sticker)
Turn ignition switch (12) to ON
CHECK the exhaust outlet (7) is clear of obstruction and flammable materials. It will get hot quickly.
Firmly pull starter handle (14 & Fig. E) until the engine starts
NOTE after each pull of the starter handle (14) control its return. DO NOT allow it to snap back towards the pump.
The engine will run at a fast idle, allow it to do this for 20 - 30 seconds
CHECK that there is water coming from the discharge hose. If no water is pumping, stop engine. Carry out priming your water pump, then restart engine
If water is still not pumping, prime the pump then start and INCREASE the engine and pump speed quickly
Slowly reduce the amount of choke (9) by moving it from left to right
Allow the engine to run at this speed for a few minutes to warm up, before adjusting the speed (10) as required.

Stopping the pump:

Reduce engine speed to its lowest move speed control (10) fully to the right
Allow engine to run at idle speed for 30 seconds
Turn ignition switch (12) to OFF position.
Turn Fuel lever (8) to OFF position fully to the left
Allow the pump and engine to cool fully before attempting to move, or carrying out any cleaning and maintenance.

Draining water:

Remove the water drain plug (23)
Tip forward (Fig F) and allow to drain fully
Replace drain plug (23)

Draining fuel:

Only drain fuel when pump has fully cooled down.
Place a suitable container underneath the fuel drain screw (17)
Unscrew the fuel drain screw (17) using a screwdriver or spanner
Allow the fuel to drain fully into the container.
Replace the draining screw (17) and tighten firmly

Cleaning:

Only clean when pump has fully cooled down.
Use a mild soapy solution and a stiff brush.
Rinse with clean water
Dry as thoroughly as possible parts of this product will corrode if left wet.

This Silverline product comes with a 3 year guarantee.

To qualify you must register this product at silverlinetools.com within 30 days of purchase. The guarantee period begins on the date of purchase as detailed on your sales receipt.

Registering your purchase

Registration is made at silverlinetools.com by selecting the Guarantee Registration button. You will need to enter the following details.

Your personal details
Details of the product and purchase information

Once this information is entered your guarantee certificate will be created in PDF format for you to print out and keep with your purchase.

Specification

Engine: 4 stroke OHC
Power: 6.5 Hp
Fuel: Unleaded
Oil type: 10W-30 mineral
Oil Qty: 0.6L
Spark plug: N9YC
Spark plug gap: 0.5 0.7mm
Fuel tank capacity: 3 6L
Max continuous run time: 14 hours
Maximum pump rate: 27m 3/hour (600l/min) (158ga/min)1/2?
Pumping elevation: 30m
Suction head: 7m
Suction hose (reinforced not included) 50mm diameter
Discharge hose: 50mm diameter
Sound Level: 99dB(A)
Dimensions: 490 x 380 x 370mm

Conforms to the following Directives:

Noise emissions for equipment for use outdoors 2000/14/EC AS amended by 2005/88/EC Annex III
Non road mobile machinery directive 97/68/EC as last amended by 2004/26/EC
Machinery directive 2006/42/EC
EN809:1998+AC:02+A1:2009
EN ISO12100-2:2003+A1:2009

Includes

Filter for hose end
2 x inserts
2 x rubber washers
3 x hose clips
Multi tool

Silverline Tools, trusted in the trade.

RRP - £359.99