US PRO TOOLS 9 Piece Damaged 8mm and 10mm Glow Plug Removal Set - NEW

US Pro Tools need we say more. US Pro Tools are made to the highest American engineering standards, which mean that they are one of the best tool manufacturers on the market.

If you want a toolkit that will remove Broken Glow Plugs without further damage then this is the set for you.

This is a professional quality 9 piece comprehensive set for removing broken or damaged glow plugs specifically where they have been sheared off just under the hex flush with then cylinder head.

Suitable for professional or diy use this set is a must have in the workshop as will save you time and money.

Instructions

Choose the no.6 socket,install it onto the glow plug,use a hammer to fix the socket with glow plug head, then try to remove the glow plug with 3/8" DR spanner.
This tool is especially for the situation when removing the glow plug, but if only the head is removed,thenplease use the other accessories to remove the rest of the glow plug from glow plug hole and replace with a new one
Insert no.4 tube into the glow plug hole,then insert a drill into no.4 tube then drill a hole with air tool.Separate the no.1 device and only choose the cone center tool and install it into the glow plug hole.Choose suitable drill no.7 or 8(7x5.5 or 9x5.5),insert the drill into no.2 drill installer.lt is important to use no. 5(3mm alley key) to lock the screw on drill installer.Then install it into cone center tool and connect with air tool to drill and also remove the hex nut from glow plug.
Before working the next step,please use the air gun to clean all the metal scrap from drilling.Choose the tap 1/4""-28 UNF from no.13,insert it into no.9 T-handle.Install it into glow plug hole and turnthe T-handle clockwise for drilling.After work just adjust the key on T-handle and remove the T-handleanti-clockwise.
Choose the tool no. 1,there are a hex 12mm bolt and 30mm hex nut and a cone center tool.Screw the no.3 bolt(1/4""-28 UNF hex 9mm) into the hex 12mm bolt and use a 9mm spanner to tighten the no.3 bolt.
Install the cone center tool and hex 12mm bolt into glow plug hole;then screw the M30 hex nut properly.Use M12 spanner to FIX the hex 12 bolt head; and use the M30 spanner to turn the M30 hex untclockwise to extract the rest part of glow plug.
Choose a tap (M10xP1.0 or M8 x1.0)from no. 11or12,install it with T-handle,and tap the glow plug hole.Remove the T-handle and replace the new glow plug.Then the work is done.

Specification Hex 12mm Spindle with Hex 30mm Nut and cone centre tool
Drill Installer
1/4" - 28 UNF Hex 8mm x2
6mm diameter tube x2
3mm allen key
9.7mm square socket
7 x 5.5 mm drill bit
9 x 5.5 mm drill bit
T handle
2 x 3.5 mm drill bits
M10 x P10
M8 x 1.0
1/4" - 28 UNF
Box Dimensions: 30cm x 20cm x 7cm RRP - ?169.99

Specification

Hex 12mm Spindle with Hex 30mm Nut and cone centre tool
Drill Installer
1/4" - 28 UNF Hex 8mm x2
6mm diameter tube x2
3mm allen key
9.7mm square socket
7 x 5.5 mm drill bit
9 x 5.5 mm drill bit
T handle
2 x 3.5 mm drill bits
M10 x P10
M8 x 1.0
1/4" - 28 UNF
Box Dimensions: 30cm x 20cm x 7cm

US Pro Tools made by professionals for professionals.

RRP - £169.99